Kody błędów

Wybrane kody usterek związane z pracą ASB

P0700 Transmission Control System Malfunction
P0701 Transmission Control System Range/Performance
P0702 Transmission Control System Electrical
P0703 Torque Converter/Brake Switch B Circuit Malfunction
P0704 Clutch Switch Input Circuit Malfunction
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
P0706 Transmission Range Sensor Circuit Range/Performance
P0707 Transmission Range Sensor Circuit Low Input
P0708 Transmission Range Sensor Circuit High Input
P0709 Transmission Range Sensor Circuit Intermittent
P0710 Transmission Fluid Temperature Sensor Circuit Malfunction
P0711 Transmission Fluid Temperature Sensor Circuit Range/Performance
P0712 Transmission Fluid Temperature Sensor Circuit Low Input
P0713 Transmission Fluid Temperature Sensor Circuit High Input
P0714 Transmission Fluid Temperature Sensor Circuit Intermittent
P0715 Input/Turbine Speed Sensor Circuit Malfunction
P0716 Input/Turbine Speed Sensor Circuit Range/Performance
P0717 Input/Turbine Speed Sensor Circuit No Signal
P0718 Input/Turbine Speed Sensor Circuit Intermittent
P0719 Torque Converter/Brake Switch B Circuit Low
P0720 Output Speed Sensor Circuit Malfunction
P0721 Output Speed Sensor Circuit Range/Performance
P0722 Output Speed Sensor Circuit No Signal
P0723 Output Speed Sensor Circuit Intermittent
P0724 Torque Converter/Brake Switch B Circuit High
P0725 Engine Speed Input Circuit Malfunction
P0726 Engine Speed Input Circuit Range/Performance
P0727 Engine Speed Input Circuit No Signal
P0728 Engine Speed Input Circuit Intermittent
P0730 Incorrect Gear Ratio
P0731 Gear 1 Incorrect Ratio
P0732 Gear 2 Incorrect Ratio
P0733 Gear 3 Incorrect Ratio
P0734 Gear 4 Incorrect Ratio
P0735 Gear 5 Incorrect Ratio
P0736 Reverse Incorrect Ratio
P0740 Torque Converter Clutch Circuit Malfunction
P0741 Torque Converter Clutch Circuit Performance or Stuck Off
P0742 Torque Converter Clutch Circuit Stuck On
P0743 Torque Converter Clutch Circuit Electrical
P0744 Torque Converter Clutch Circuit Intermittent
P0745 Pressure Control Solenoid Malfunction
P0746 Pressure Control Solenoid Performance or Stuck Off
P0747 Pressure Control Solenoid Stuck On
P0748 Pressure Control Solenoid Electrical
P0749 Pressure Control Solenoid Intermittent
P0750 Shift Solenoid A Malfunction
P0751 Shift Solenoid A Performance or Stuck Off
P0752 Shift Solenoid A Stuck On
P0753 Shift Solenoid A Electrical
P0754 Shift Solenoid A Intermittent
P0755 Shift Solenoid B Malfunction
P0756 Shift Solenoid B Performance or Stuck Off
P0757 Shift Solenoid B Stuck On
P0758 Shift Solenoid B Electrical
P0759 Shift Solenoid B Intermittent
P0760 Shift Solenoid C Malfunction
P0761 Shift Solenoid C Performance or Stuck Off
P0762 Shift Solenoid C Stuck On
P0763 Shift Solenoid C Electrical
P0764 Shift Solenoid C Intermittent
P0765 Shift Solenoid D Malfunction
P0766 Shift Solenoid D Performance or Stuck Off
P0767 Shift Solenoid D Stuck On
P0768 Shift Solenoid D Electrical
P0769 Shift Solenoid D Intermittent
P0770 Shift Solenoid E Malfunction
P0771 Shift Solenoid E Performance or Stuck Off
P0772 Shift Solenoid E Stuck On
P0773 Shift Solenoid E Electrical
P0774 Shift Solenoid E Intermittent
P0775 Pressure Control Solenoid „B”
P0776 Pressure Control Solenoid „B” Performance or Stuck off
P0777 Pressure Control Solenoid „B” Stuck On
P0778 Pressure Control Solenoid „B” Electrical
P0779 Pressure Control Solenoid „B” Intermittent
P0780 Shift Malfunction
P0781 1-2 Shift Malfunction
P0782 2-3 Shift Malfunction
P0783 3-4 Shift Malfunction
P0784 4-5 Shift Malfunction
P0785 Shift/Timing Solenoid Malfunction
P0786 Shift/Timing Solenoid Range/Performance
P0787 Shift/Timing Solenoid low
P0788 Shift/Timing Solenoid High
P0789 Shift/Timing Solenoid Intermittent
P0790 Normal/Performance Switch Circuit Malfunction
P0791 Intermediate Shaft Speed Sensor Circuit
P0792 Intermediate Shaft Speed Sensor Circuit Range/Performance
P0793 Intermediate Shaft Speed Sensor Circuit No signal
P0794 Intermediate Shaft Speed Sensor Circuit Intermittent
P0795 Pressure Control Solenoid „C”
P0796 Pressure Control Solenoid „C” Performance or Stuck off
P0797 Pressure Control Solenoid „C” Stuck On
P0798 Pressure Control Solenoid „C” Electrical
P0799 Pressure Control Solenoid „C” Intermittent
P0801 Reverse Inhibit Control Circuit Malfunction
P0803 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction
P0804 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction
P0805 Clutch Position Sensor Circuit Malfunction
P0806 Clutch Position Sensor Circuit Range/Performance Malfunction
P0807 Clutch Position Sensor Circuit Low Malfunction
P0808 Clutch Position Sensor Circuit High Malfunction
P0809 Clutch Position Sensor Circuit Intermittent Malfunction
P0810 Clutch Position Control Error
P0811 Excessive Clutch Slippage
P0812 Reverse Input Circuit
P0813 Reverse Output Circuit
P0814 Transmission Range Display Circuit
P0815 Upshift Switch Circuit
P0816 Downshift Switch Circuit
P0817 Starter Disable Circuit
P0818 Driveline Disconnect Switch Input Circuit
P0820 Gear Lever X – Y Position Sensor Circuit
P0821 Gear Lever X Position Circuit
P0822 Gear Lever Y Position Circuit
P0823 Gear Lever X Position Circuit Intermittent
P0824 Gear Lever Y Position Circuit Intermittent
P0825 Gear Lever Push – Pull Switch (Shift Anticipate)
P0830 Clutch Pedal Switch „A” Circuit
P0831 Clutch Pedal Switch „A” Circuit Low
P0832 Clutch Pedal Switch „A” Circuit High
P0833 Clutch Pedal Switch „B” Circuit
P0834 Clutch Pedal Switch „B” Circuit Low
P0835 Clutch Pedal Switch „B” Circuit High
P0836 Four Wheel Drive (4WD) Switch Circuit
P0837 Four Wheel Drive (4WD) Switch Circuit Range/Performance
P0838 Four Wheel Drive (4WD) Switch Circuit Low
P0839 Four Wheel Drive (4WD) Switch Circuit High
P0840 Transmission Fluid Pressure Sensor/Switch „A” Circuit
P0841 Transmission Fluid Pressure Sensor/Switch „A” Circuit Range/Performance
P0842 Transmission Fluid Pressure Sensor/Switch „A” Circuit Low
P0843 Transmission Fluid Pressure Sensor/Switch „A” Circuit High
P0844 Transmission Fluid Pressure Sensor/Switch „A” Circuit Intermittent
P0845 Transmission Fluid Pressure Sensor/Switch „B” Circuit
P0846 Transmission Fluid Pressure Sensor/Switch „B” Circuit Range/Performance
P0847 Transmission Fluid Pressure Sensor/Switch „B” Circuit Low
P0848 Transmission Fluid Pressure Sensor/Switch „B” Circuit High
P0849 Transmission Fluid Pressure Sensor/Switch „B” Circuit Intermittent
P1701 Transmission Solenoid Malfunction (Mazda)
P1703 Brake On/Off Switch (Mazda)
P1703 Brake On/Off Switch Out Of Range (Ford)
P1705 Automatic Transaxle (Acura)
P1705 Transmisson Range Sensor Out Of Range (Ford)
P1705 Transmisson Range Sensor (Mazda)
P1706 Automatic Transaxle (Acura)
P1709 Automatic Transaxle (Acura)
P1709 Park/Neutral Position Switch (Mazda)
P1709 Park/Neutral Position Switch Out Of Range (Ford)
P1710 Automatic Transaxle (Acura)
P1711 Transmission Fluid Temperature Sensor (Mazda)
P1713 Automatic Transaxle (Acura)
P1719 Skip Shift Solenoid Circuit (Chrysler)
P1729 4×4 Low Switch (Mazda)
P1729 4×4 Low Switch Malfunction (Ford)
P1738 Automatic Transaxle (Acura)
P1739 Automatic Transaxle (Acura)
P1740 Automatic Transaxle (Acura)
P1746 EPC Solenoid Failed Low (Mazda)
P1747 EPC Solenoid Short Circuit (Mazda)
P1749 EPC Solenoid Open Circuit (Mazda)
P1751 Shift Solenoid #1 (SS1) (Mazda)
P1753 Automatic Transaxle (Acura)
P1754 Coast Clutch Solenoid (Mazda)
P1756 GOV Press Not Equal To Target @ 15-20 PSI (Chrysler)
P1756 Shift Solenoid #2 (SS2) (Mazda)
P1757 GOV Press Not Equal To Target @ 15-20 PSI (Chrysler)
P1758 Automatic Transaxle (Acura)
P1761 Shift Solenoid #3 (SS3) (Mazda)
P1762 Gov Press Sen Offset Volts Too Low or high(Chrysler)
P1763 Governor Pressure Sensor Volts Too High (Chrysler)
P1764 Governor Pressure Sensor Volts Too Low (Chrysler)
P1765 Trans 12 Volt Supply Relay CTRL Circuit (Chrysler)
P1768 Automatic Transaxle (Acura)
P1773 Automatic Transaxle (Acura)
P1778 Automatic Transaxle (Acura)
P1780 Transmission Control Switch (Mazda)
P1780 Transmission Control Switch Out Of Range(Ford)
P1781 4×4 Switch Out Of Range (Ford)
P1781 4×4 Low Switch (Mazda)
P1783 Transmission Over Temperature Condition (Mazda)
P1786 Automatic Transaxle (Acura)
P1790 Automatic Transaxle (Acura)
P1791 Automatic Transaxle (Acura)
P1792 Automatic Transaxle (Acura)
P1794 Automatic Transaxle (Acura)
P1810 TFP Valve Position Switch Circuit (GM)
P1811 Maximum Adapt and Long Shift (GM)
P1819 Internal Mode Switch – No Start/Wrong Range (GM)
P1820 Internal Mode Switch Circuit A Low (GM)
P1822 Internal Mode Switch Circuit B High (GM)
P1823 Internal Mode Switch Circuit P Low (GM)
P1825 Internal Mode Switch – Invalid Range (GM)
P1826 Internal Mode Switch Circuit C High (GM)
P1860 TCC PWM Solenoid Circuit Electrical (GM)
P1887 TCC Release Switch Circuit (GM)
P1899 Park/Neutral Position Switch Stuck In Park or In Gear (CHRYSLER)

KODY MERCEDES

P2000 Component N15/3 (ETC control module) is faulty.
P2000 Component N15/3(ETC control module) is faulty.

P2001 Component N15/3 (ETC control module) is faulty.
P2002 Component N15/3(ETC control module) is faulty.
P2003 Component N15/3(ETC control module) is faulty.
P2004 Component N15/3(ETC control module) is faulty.
P2005 Component N15/3(ETC control module) is faulty.
P2006 Component N15/3(ETC control module) is faulty.
P2007 Component N15/3(ETC control module) is faulty.
P2008 Component N15/3(ETC control module) is faulty.
P2009 Component N15/3(ETC control module) is faulty.
P200A Component N15/3(ETC control module) is faulty.
P200B Component N15/3(ETC control module) is faulty.
P200C Component N15/3(ETC control module) is faulty.
P200D Component N15/3 (ETC control module) is faulty.
P200D Component N15/3(ETC control module) is faulty.
P200E-001 component N15/3 (EGS controller) trouble stored.[P0702]
P200E-002 component N15/3 (EGS controller) trouble stored.[P0753]
P200E-004 component N15/3 (EGS controller) trouble stored.[P0758]
P200E-008 component N15/3 (EGS controller) trouble stored.[P0763]
P200E-016 component N15/3 (EGS controller) trouble stored.[P0743]
P200E-032 component N15/3 (EGS controller) trouble stored.[P0748]
P200E-064 component N15/3 (EGS controller) trouble stored.[P0748]
P200E-128 component N15/3 (EGS controller) trouble stored.[P0702]
P200F-001 component N15/3 (EGS controller) trouble stored.[P0715]
P200F-002 component N15/3 (EGS controller) trouble stored.[P0705]
P200F-004 component N15/3 (EGS controller) trouble stored.[P0720]
P200F-008 component N15/3 (EGS controller) trouble stored.[P0700]
P200F-016 component N15/3 (EGS controller) trouble stored.[P0700]
P200F-032 component N15/3 (EGS controller) trouble stored.[P0740]
P200F-064 component N15/3 (EGS controller) trouble stored.[P0730]
P2010 Control module N15/3(ETC control module is not coded.
P2015 check start control.Circuit open
P2015 check start control.short to ground
P2015 check start control.Short
P2021-001 starter relay,positive short
P2021-002 starter relay,overload/wire open cause short
P2026-001 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error
P2026-002 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error
P2026-004 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error
P2026-008 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal error
P2026-016 CAN BUS signal from N15/3 (EGS controller) controller,CAN BUS signal interrupt
P2031 no signal or error signal from N15/5 (electronic shift lever mode controller)
P203D-001 N15/6 (automatic shift transmission controller) urgency start,controller
P203D-002 N15/6 (automatic shift transmission controller) urgency start,controller
P203D-004 N15/6 (automatic shift transmission controller) urgency start,controller
P203E BUS signal error from combination instrument (P0600)
P203E No CAN message from instrument cluster or message faulty.(P0600)
P203E-001 speed auto control,electronic accelerograph pedal urgency start
P203E-002 speed auto control,speed meter switch position error
P205E Component N15/3 (ETC control module) memory is fault.(P0702)
P205E fault stored in component N15/3 (EGS controller).(P0702)
P205F Component N15/3 (ETC control module) memory is fault.(P0753)
P205F fault stored in component N15/3 (EGS controller).(P0753)
P2060 Component N15/3 (ETC control module) memory is fault.(P0758)
P2060 fault stored in component N15/3 (EGS controller).(P0758)
P2061 Component N15/3 (ETC control module) memory is fault.(P0763)
P2061 fault stored in component N15/3 (EGS controller).(P0763)
P2062 Component N15/3 (ETC control module) memory is fault.(P0743)
P2062 fault stored in component N15/3 (EGS controller).(P0743)
P2063 Component N15/3 (ETC control module) memory is fault.(P0748)
P2063 fault stored in component N15/3 (EGS controller).(P0748)
P2064 Component N15/3 (ETC control module) memory is fault.(P0748)
P2064 fault stored in component N15/3 (EGS controller).(P0748)
P2065 Component N15/3 (ETC control module) memory is fault.(P0702)
P2065 fault stored in component N15/3 (EGS controller).(P0702)
P2066 Component N15/3 (ETC control module) memory is fault.(P0715)
P2066 fault stored in component N15/3 (EGS controller).(P0715)
P2067 Component N15/3 (ETC control module) memory is fault.(P0705)
P2067 fault stored in component N15/3 (EGS controller).(P0705)
P2068 Component N15/3 (ETC control module) memory is fault.(P0720)
P2068 fault stored in component N15/3 (EGS controller).(P0720)
P2069 Component N15/3 (ETC control module) memory is fault.(P0700)
P2069 fault stored in component N15/3 (EGS controller).(P0700)
P206A Component N15/3 (ETC control module) memory is fault.(P0700)
P206A fault stored in component N15/3 (EGS controller).(P0700)
P206B Component N15/3 (ETC control module) memory is fault.(P0740)
P206B fault stored in component N15/3 (EGS controller).(P0740)
P206D Component N15/3 (ETC control module) memory is fault.(P0730)
P206D fault stored in component N15/3 (EGS controller).(P0730)
P206E Control module ME-SFI 2.8 is incorrectly coded (coded to MT,vehicle has AT)
P206E ME 2.7 controller incorrect coded (according to AT code,car has MT)
P206F Control module ME-SFI  fault in the CAN communication with control module N15/3
P206F ME 2.7 controller incorrectly coded or communication error with N15/3
P2070 as component N15/3 (EGS controller) voltage is too low,transmission variables can not be checked
P2070 Transmission version cannot be checked because of undervoltage at component N15/3
P2071 Start enable of DAS not sent
P2077 Read fault memory from control unit N15/6 (Sprintshift control module) and rectify faults.
P2078 Read fault memory from control unit N15/6 (Sprintshift control module) and rectify faults.
P2079 CAN signal ‚Vehicle speed limit’
P207A CAN signal ‚Vehicle speed limit’
P207B Read fault memory from control unit Transmission and rectify faults.
P20D2 CAN transmission error of torque request from control module N63/1 (DTR control module)
P20D5 controller N15/3 (EGS controller) torque request error.(P0702)
P20D5 The torque request from control module N15/3 (ETC control module) is implausible.(P0702)
P20D6 CAN transmission error of torque request from control module N15/3 (ETC control module)(P0702)
P20D6 controller N15/3 (EGS controller) torque request BUS transmission error (P0702)
P20D7 CAN transmission error of torque request from control module N15/3 (ETC control module)(P0702)
P20D7 controller N15/3 (EGS controller) torque request BUS transmission error (P0702)
P20D8 electronic stable program malfunction
P20DA CAN transmission error of torque request from control module N47-5 (ESP control module)
P20DA controller N47-5 (ESP controller) torque request BUS transmission error
P20DB CAN transmission error of torque request from control module N47-5 (ESP control module)
P20DB controller N47-5 (ESP controller) torque request BUS transmission error
P20E3 Voltage supply of component B37 (Pedal value sensor)(P0120)
P20E4 error signal from component S9/1 (brake light switch)
P20E4 Implausible signal from component S9/1 (Stop lamp switch)
P20E5 CAN transmission error of signal from component S9/1 (Stop lamp switch)
P20E5 component S9/1 (brake light switch) signal BUS transmission error
P20E6 CAN transmission error of signal from component S9/1 (Stop lamp switch)
P20E6 component S9/1 (brake light switch) signal BUS transmission error
P2100 Component Y3/6y3 (1-2 and 4-5 shift solenoid valve) is faulty.
P2100 The internal electrical check of component Y3/6y3(1-2 and 4-5 shift solenoid valve) has failed.
P2101 Component Y3/6y3(1-2 and 4-5 shift solenoid valve) has a short circuit to ground.
P2102 Component Y3/6y5 (2-3 shift solenoid valve) is faulty.
P2102 The internal electrical check of Component Y3/6y5(2-3 shift solenoid valve) has failed.
P2103 Component Y3/6y5(2-3 shift solenoid valve) has a short circuit to ground.
P2104 Component Y3/6y4 (3-4 shift solenoid valve) is faulty.
P2104 The internal electrical check of Component Y3/6y4(3-4 shift solenoid valve) has failed.
P2105 Component Y3/6y4(3-4 shift solenoid valve) has a short circuit to ground.
P2106 Component Y3/6y6 (Torque converter lockup PWM solenoid valve) is faulty.
P2106 The internal electrical check of Component Y3/6y6(Torque converter lockup PWM solenoid valve) has failed.
P2107 Component Y3/6y1 (Modulating pressure control solenoid valve) is faulty.
P2107 The internal electrical check of Component Y3/6y1(Modulating pressure control solenoid valve) has failed.
P2108 Component Y3/6y2 (Shift pressure control solenoid valve) is faulty.
P2108 The internal electrical check of Component Y3/6y2(Shift pressure control solenoid valve) has failed.
P2109 Component Y66/1(Reversing and parking lock solenoid) has short circuit or no connection.
P210A The cable to component K38/3(Starter lockout relay) has short circuit or no connection.
P2200 Component Y3/6n2(speed sensor 2) is faulty or the sensor supply has Short circuit.
P2203 Component Y3/6n3 (speed sensor 3) is faulty.
P2206 No signal from output speed sensor
P2207 The value of component Y3/6n3 (speed sensor 3) is implausible.
P220A The speed comparison of Y3/6n2 or Y3/6n3 is implausible.
P220B The speed of Y3/6n2 or Y3/6n3 is too high.
P2210 Selector lever coding is invalid.
P2211 The selector lever is in an intermediate position.
P2212 The selector lever position is implausible.
P2220 Component Y3/6s1(Starter lockout contact) or component Y3/6b1 (ATF temperature sensor) is faulty or both.
P2221 The signal of component Y3/6b1 (ATF temperature sensor) and (or) Y3/6s1 (Starter lockout contact) is implausible.
P2222 The signal of component Y3/6b1 (ATF temperature sensor) and (or) Y3/6s1 (Starter lockout contact) is implausible.
P2300 CAN communication is faulty.
P2300 CAN communication with other control units installed in this vehicle is not possible.
P2301 CAN communication is faulty.
P2301 CAN communication with other control units installed in this vehicle is not possible.
P2318 Fault in CAN communication with control unit N15/5 (electronic selector lever module control module)
P2318 One or more messages from control unit N15/5(electronic selector lever module control module
P2333 The CAN signal from control module N15/5 (electronic selector module control module) is faulty.
P2333 The CAN signals sent from control unit N15/5(electronic selector module control module)
P2338 The CAN signal from control module N15/5 (electronic selector lever module control module) is faulty.
P2338 The CAN signals sent from control unit N15/5(electronic selector lever module control module
P240C The CAN signal for the selector lever position from component N15/5 .
P240C The selector lever position sent from control unit N15/5via the CAN bus is implausible
P2500 The transmission has an impermissible transmission ratio
P2502 The gear is implausible or the transmission is slipping.
P2503 The gear comparison is negative or the target gear is not reached.
P2510 The torque converter lock-up clutch causes impermissible closing.
P2511 Engaging of torque converter lockup clutch not permitted.
P2511 The torque converter lock-up clutch has excessive power consumption.
P2512 Actuation of torque converter lockup clutch is not possible
P2520 The feedback through the transmission protection is not maintained.
P2600 The voltage supply of circuit 87 has undervoltage.
P2601 The voltage supply of circuit 87 has overvoltage.
P2602 The voltage supply of the valves is faulty.
P2603 The voltage supply of the speed sensors is faulty.